All Xirgo Products

The power harness for the CP4 and CP4S, carrying battery positive, ignition positive and battery negative. One ships in every CP4S box; order here ...

The external GPS and GLONASS antenna module for the CP4 and CP4S. The recorder relies on this module for positioning, so a failed or damaged unit m...

The mounting bracket for the CP4 and CP4S recorder. One ships in every CP4S box; order here as a replacement or where a second mounting position is...

The video and audio output harness for the CP4 and CP4S, carrying the video-out feed to an in-cab monitor plus the RPM, speed and alarm I/O trigger...

A tubular mounting bracket for attaching an SVA035 camera to the tube frame of a side mirror assembly. Mirror-arm mounting gives the best blind-spo...

A wired remote panic button for CP4S and CRX-S systems. Pressing it triggers an event recording, preserving footage around an incident that would o...

The standard mounting bracket for all SVA035 cameras, including the accessory package version. A spare part for installations where the original br...

A splitter that takes one Aviation camera cable run and feeds two cameras from it. Useful where two cameras sit close together at the far end of a ...

A converter for mixed-generation installations, taking a 4-pin female Aviation connector to a 4-pin female DIN. Use it where an Aviator camera need...

A short adapter that converts an Aviator male connector to a Type B male, letting Aviator-terminated cabling connect to newer Type B camera hardwar...

The complete tractor-trailer quick disconnect kit. Same trailer hook-up as the SVA-20TT-EXT-A but supplied with the adapter and converter cables in...

A trailer hook-up extension for tractor-trailer installations, letting a rear camera on the trailer connect to a recorder in the cab. Cables are sp...

A 15m camera cable for runs the standard 5m cannot reach: rear-mounted cameras on box trucks and buses, cargo-area domes, and any position at the f...

The standard 5m camera cable for CP4S and CRX-S installations. Every bare SVA camera requires one of these to reach the recorder; the -5B kit versi...

The Aviator-connector version of the 5m camera cable, for installations built around legacy Aviator camera hardware rather than the newer Type B pl...

A 4m two-in-one extension built specifically for the SVA055 combination camera. Because the SVA055 carries both a road-facing and a driver-facing c...

The four-channel version of the 7" in-cab monitor, with a separate alarm trigger for each channel. Where the single-channel model shows one view, t...

A commercial-grade 7" in-cab monitor that turns a recorder into a live driver aid. Wired to the video output of a CP4S or CRX-S, it gives the drive...

A tamper-resistant steel locking enclosure for the CP4S. The recorder mounts inside and the enclosure locks, which matters on vehicles where a driv...

The Wi-Fi version of the CP4S 4-channel HD vehicle recorder. Identical in recording capability to the cellular model but without the LTE modem, it ...

The CP4S is a compact cloud-connected mobile DVR that records up to four HD cameras plus full telematics data. Built for North American fleets on 4...

A replacement Torx key for the KP2. Required to open the side cover for SD card access, so a lost key means no card access on a deployed camera. To...

The KP2 side plate kit, containing the side cover and the fasteners that secure it. The side cover protects the SD card slot, so a damaged or missi...

The KP2 installation tool, used for trim removal and cable routing during a windshield install. Installation tool for KP2 fitting For trim removal ...

The KP2 replacement installation kit, containing the consumables used up during a fit: cable ties, a Torx key, alcohol preparation pads and 3M adhe...

The hardwired KP2 power adaptor, connecting to constant power, ignition and ground rather than a diagnostic port. This is the professional install:...

The KP2 mounting bracket, supplied with a 2.73m cable. This is the assembly that holds the KP2 to the windshield, and it is a replacement part for ...

Double-sided 3M adhesive tape for the KP2 mounting pad, supplied as a single piece. Use it when remounting a KP2 to the windshield after removal, s...

A wireless Bluetooth panic button for KP2 systems. Pressing it flags the moment as an event so the footage is preserved and uploaded rather than ov...

A privacy cover for the KP2 driver-facing camera. It physically blocks the lens, which satisfies driver privacy requirements and union agreements i...

A 2m extension for the KP2 remote interior cameras, doubling the standard 2m lead to 4m. For high-cab vehicles and split-windshield installations w...

A 2m extension cable for the KP2, used where the standard cable run does not reach the chosen power source or the camera needs mounting further fro...

A cigarette lighter power adaptor for the KP2. The fastest possible installation and fully reversible, which makes it the right choice for leased v...

The heavy-duty KP2 connection, for trucks and equipment with a J1939 nine-pin Deutsch port instead of OBD-II. Acts as a splitter, leaving an open J...

The simplest way to power a KP2: plug it into the vehicle's OBD-II port and the install is done. Voltage monitoring handles ignition detection and ...

The driver-facing camera blank plate for the KP2. It fills the module bay on units running road-facing only, keeping dust and debris out. One ships...

The Xirgo IOX auto-pairing cable, connecting a KP2 or XVD-302 camera to a Geotab GO9 or GO10 telematics device. Auto-pairing means the two devices ...

The pass-through version of the KP2 OBD-II power cable. It powers the KP2 while keeping a female OBD-II port available, so a diagnostic tool or a s...

A mixed-standard splitter for vehicles carrying both diagnostic types. Takes a female OBD-II input and provides one J1939 female and one J1939 male...

An OBD-II splitter that turns one port into two. Single male OBD-II connector into two female OBD-II connectors, so a KP2 and a second device can s...

An angled block wedge for KP2 installations in trucks with a split windshield. The wedge corrects the mounting angle so the camera continues to fac...

The no-infrared version of the KP2 remote interior camera. Functionally identical to the KP2-INTCAM-REM but with the IR LEDs omitted, which suits i...

A remote driver-facing interior camera for KP2 installations where the snap-on module cannot be positioned effectively. Supplied with a 2m cable, i...

The driver-facing camera module that unlocks Driver State Monitoring on the KP2. It snaps directly onto the KP2 body with no additional cabling or ...

The KP2 is Xirgo's modular road-facing video telematics device, combining a 2MP HD dash camera, GPS tracking and 4G/LTE connectivity in a single wi...